Comnet CNGE2FE8MSPOE Technical Information Page 95
- Page / 162
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
88
6.19.2 Port Configuration
This web page provides the port configuration interface for RSTP. You can assign higher or
lower priority to each port. Rapid spanning tree will have the port with the higher priority in
forwarding state and block other ports to make certain that there is no loop in the LAN.
Select the port in the port column field.
Path Cost: The cost of the path to the other bridge from this transmitting bridge at the
specified port. Enter a number 1 through 200,000,000.
Priority: Decide which port should be blocked by setting its priority as the lowest. Enter
a number between 0 and 240. The value of priority must be the multiple of 16.
Admin P2P: The rapid state transitions possible within RSTP are dependent upon
whether the port concerned can only be connected to exactly another bridge (i.e. it is
served by a point-to-point LAN segment), or can be connected to two or more bridges
(i.e. it is served by a shared medium LAN segment). This function allows the P2P
status of the link to be manipulated administratively. True means the port is regarded
as a point-to-point link. False means the port is regarded as a shared link. Auto means
the link type is determined by the auto-negotiation between the two peers.
Admin Edge: The port directly connected to end stations won’t create bridging loop in
the network. To configure the port as an edge port, set the port to “True” status.
Admin Non Stp: The port includes the STP mathematic calculation. True is not
including STP mathematic calculation. False is including the STP mathematic
calculation.
Click .
- CNGE2FE8MSPOE 1
- FCC Warning 2
- CE Mark Warning 2
- Content 3
- Chapter 1 Introduction 8
- 1.2 Software Features 12
- 1.3 Package Contents 15
- 2.1 Physical Dimension 16
- 2.2 Front Panel 16
- 2.3 Top View 17
- 2.4 LED Indicators 18
- 3.1 Installation Steps 20
- 3.2 DIN-Rail Mounting 21
- 3.4 Wiring the Power Inputs 25
- 3.6 Cabling 27
- Transceiver Inserted 28
- Remove LC connector 30
- 4.1 X-Ring Application 33
- 4.3 Dual Homing Application 35
- Chapter 5 Console Management 36
- Console login interface 38
- 5.4 CLI Management 39
- 5.5 Commands Level 39
- 6.3 System Login 42
- 6.4 System Information 43
- 6.5 IP Configuration 44
- IP configuration interface 45
- 6.6 DHCP Server 46
- 6.6.1 System configuration 47
- 6.6.2 Client Entries 48
- 6.6.3 Port and IP Bindings 49
- 6.7 TFTP 50
- 6.7.2 Restore Configuration 51
- 6.7.3 Backup Configuration 52
- 6.8 System Event Log 53
- SMTP Configuration interface 56
- 6.9 Fault Relay Alarm 59
- 6.10 SNTP Configuration 60
- SNTP Configuration interface 63
- 6.11 IP Security 64
- IP Security interface 65
- 6.12 User Authentication 66
- 6.13 Port Statistics 67
- Port Statistics interface 68
- 6.14 Port Control 69
- Port Control interface 70
- 6.15 Port Trunk 71
- LACP disabled 73
- LACP enabled 75
- 6.15.3 State Activity 79
- State Activity of Switch 2 80
- 6.16 Port Mirroring 81
- 6.17 Rate Limiting 82
- 6.18 VLAN configuration 84
- 6.18.1 Port-based VLAN 85
- 6.18.2 802.1Q VLAN 88
- 802.1Q Configuration 89
- Group Configuration 91
- 6.19 Rapid Spanning Tree 93
- 6.19.2 Port Configuration 95
- 6.20 SNMP Configuration 97
- 6.20.2 Trap Configuration 99
- 6.20.3 SNMPV3 Configuration 100
- 6.21 QoS Configuration 103
- QoS Configuration interface 104
- 6.21.2 Port-based Priority 105
- 6.21.3 COS Configuration 105
- 6.21.4 TOS Configuration 105
- 6.22 IGMP Configuration 107
- IGMP Configuration interface 108
- 6.23 X-Ring 109
- X-ring Interface 110
- 6.24 LLDP Configuration 111
- 6.25.1 System Configuration 112
- 6.25.2 Port Configuration 114
- 6.25.3 Misc Configuration 116
- 6.26 MAC Address Table 117
- 6.26.2 MAC Filtering 119
- 6.26.3 All MAC Addresses 120
- 6.27 Power over Ethernet 123
- 6.28 Factory Default 125
- 6.29 Save Configuration 126
- 6.30 System Reboot 127
- Troubles shooting 128
- RJ45 Pin Assignments 129
- Cross over cable schematic 130
- Cross over cables schematic 132
- RJ45 Pin Assignment of PoE 133
- Appendix B—Command Sets 135
- Halt and perform a cold 136
- Port Commands Set 138
- Trunk Commands Set 141
- VLAN Commands Set 142
- Spanning Tree Commands Set 144
- QOS Commands Set 147
- IGMP Commands Set 147
- LLDP Commands Set 149
- SNMP Commands Set 150
- Port Mirroring Commands Set 152
- 802.1x Commands Set 153
- TFTP Commands Set 155
- SNTP Commands Set 159
- X-ring Commands Set 160
- PoE Commands Set 161
- Communication Networks 162
Related products and manuals for Networking Comnet CNGE2FE8MSPOE
Networking Comnet CNGE24MS Specifications
(108 pages)
(108 pages)
Networking Comnet CWFE8MS/DIN User Manual
(20 pages)
(20 pages)
Networking Comnet CWGE28FX4TX24MS Specifications
(117 pages)
(117 pages)
Networking Comnet CNGE2FE8MSPOE User Manual
(32 pages)
(32 pages)
Networking Comnet CNGE24MS User Manual
(82 pages)
(82 pages)
© 2020, manymanuals.com. All rights reserved. | 0.770 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals