Comnet CNVETX1 Datasheet Page 85
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INS_CNVETX1_REV– 06/10/13 PAGE 85
INSTALLATION AND OPERATION MANUAL CNVETX1
TECH SUPPORT: 1.888.678.9427
Setting up the Clock
You can set up an NTP (Network Time Protocol) server for time synchronization. You can also set
up the local time zone as well as daylight saving time for the About pane.
The board supports the use of NTP to synchronize the board’s time to an external clock. This is
required for maintaining a long streaming session, compensating for clock skew between the
board and the host computer. For it to work correctly the host computer must either be the NTP
server or it must synchronize to the same NTP server as the board.
Optionally you can set the on-board Real Time Clock according to the current time of your PC.
To set up the clock:
1. In the left pane select the System menu, and select Clock Setup.
The right pane displays the Clock Setup area.
Figure 82: Change Clock Setup
To enable NTP, check the Use SNTP box and enter the IP address of your server.
- or -
If you are not using SNTP, select Set Time to set the unit’s clock according to your PC’s time.
For the time to be correctly displayed, make sure to set both the Local Time Zone and the
Daylight Savings settings.
2. In the Local Time Zone textbox, enter a value between -12 and +13 (the offset relative to GMT).
3. Check the Daylight Savings Time box if DST is presently used in your region.
- VIDEO ENCODER/DECODER UNIT 1
- About This Guide 2
- About ComNet 3
- Contents 4
- Contents, continued 5
- Overview 6
- Abbreviations List 7
- Introduction 9
- Software Features 10
- Hardware Overview 12
- Label Description 13
- ANALYTICS Analytics Engine On 13
- PWR Power (DSP Running) 13
- Connecting the Cables 15
- Getting Started 18
- Figure 8: General Sub Menus 19
- Figure 9: The About Page 20
- Resets user password 22
- Changing system password 22
- Returns to factory defaults 22
- Changing Web Language 22
- Figure 10: Enter Password 24
- Monitoring Live Video 25
- Alarms and Contact Closures 26
- Closures 27
- 3. Select Set Relay 27
- Figure 14: PTZ Commands Page 28
- Figure 17: Connection Type 30
- Figure 20: Select Bit Count 31
- Figure 21: Select Stop Bits 32
- Figure 22: Select Parity 32
- Figure 23: PTZ Commands 33
- Table 7: PTZ Movement Control 34
- Panning a PTZ Camera 35
- Figure 27: PTZ Camera at 40° 36
- Figure 28: Speed Settings 36
- Figure 29: Zoom Area 38
- Figure 30: Focus Area 38
- Figure 31: Iris Area 38
- Zooming the Camera 39
- Focusing the Camera 41
- Symbol Description 42
- GoTo preset location 42
- Define preset 42
- Delete preset 42
- Figure 38: Pattern Area 43
- Table 11: Pattern Symbols 43
- Audio/Video Configuration 44
- 4. Select Save 48
- Figure 44: OSD Parameters 49
- Table 5 – UTC Time Zones 53
- Figure 54: MJPEG Settings 61
- Figure 56: QuickTime Window 63
- Figure 57: Insert URL 63
- Figure 59: No Active Streams 64
- Figure 65: Video Settings 67
- Figure 67: Audio Settings 71
- 3. Select Save 72
- Managing System Settings 73
- Figure 72: Serial Port Modes 75
- Network Settings 78
- Changing the IP Address 81
- Figure 78: System Reset 82
- Changing the User Password 84
- Setting up the Clock 85
- Configuring the SNMP Settings 87
- Configuring Operation Mode 89
- Updating the Firmware 90
- System Administration 91
- Resetting the User Password 92
- 2. Select Save 93
- Reset to Factory Defaults 94
- Change Web Interface Language 97
- Configuring Local Storage 99
- Media Files 100
- SD Maintenance 101
- Decoding Video 102
- Video Type 103
- TECH SUPPORT: 1.888.678.9427 104
- Figure 98: MPEG-2 CODEC 105
- Figure 99: MPEG-4 CODEC 106
- Figure 100: H.264 CODEC 107
- Figure 101: MJPEG CODEC 108
- Figure 103: Audio Settings 110
- Display Configuration 111
- 7. Select OK 114
- Figure 113: URL Input Dialog 116
- RTSP URI Format 117
- General Video Parameters 118
- MJPEG Parameter 118
- MPEG-2 Parameters 118
- MPEG-4 Parameters 119
- H.264 Parameters 119
- General Audio Parameters 120
- PCMA and PCMU Parameters 120
- Multicast Parameters 120
- ComNet Customer Service 122
- Contact Information 122
© 2020, manymanuals.com. All rights reserved. | 7.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals