Comnet CNVETX1 Datasheet Page 70
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INS_CNVETX1_REV– 06/10/13 PAGE 70
INSTALLATION AND OPERATION MANUAL CNVETX1
TECH SUPPORT: 1.888.678.9427
MJPEG
You can set the MJPEG video CODEC setting of Q for the cameras. The range for the quality
adjustment is 1 to 99. The default setting is 75. At a higher setting, the bit rate will be higher.
Quality settings above 75 will result in higher bit rates with little gain in quality and are therefore
not recommended.
To set the MJPEG parameters:
1. In the CODEC drop down list select MJPEG.
2. In the Camera text-box enter the number of cameras per video source.
3. In the Video Standard drop down list, select PAL or NTSC.
4. In the Image Size drop down list, select the image size of the video stream. The image size can
be adjusted between QCIF, CIF, and 4CIF.
5. In the Quality text-box enter a Q value for the camera between 1 and 99.
6. Select Save to save the settings.
Multicast Network Settings
In the Multicast Network Settings section, set the Multicast Video Address and the Multicast Video
Port.
Figure 66: Multicast Network Settings
To set multicast Network Settings:
1. In the Multicast Video Address text box, enter the required multicast address. The range
of addresses that can be used is specified by the RFC 3171 standard as 224.0.0.0 to
239.255.255.255.
2. In the Multicast Video Port text-box enter the required port.
3. Select Save.
- VIDEO ENCODER/DECODER UNIT 1
- About This Guide 2
- About ComNet 3
- Contents 4
- Contents, continued 5
- Overview 6
- Abbreviations List 7
- Introduction 9
- Software Features 10
- Hardware Overview 12
- Label Description 13
- ANALYTICS Analytics Engine On 13
- PWR Power (DSP Running) 13
- Connecting the Cables 15
- Getting Started 18
- Figure 8: General Sub Menus 19
- Figure 9: The About Page 20
- Resets user password 22
- Changing system password 22
- Returns to factory defaults 22
- Changing Web Language 22
- Figure 10: Enter Password 24
- Monitoring Live Video 25
- Alarms and Contact Closures 26
- Closures 27
- 3. Select Set Relay 27
- Figure 14: PTZ Commands Page 28
- Figure 17: Connection Type 30
- Figure 20: Select Bit Count 31
- Figure 21: Select Stop Bits 32
- Figure 22: Select Parity 32
- Figure 23: PTZ Commands 33
- Table 7: PTZ Movement Control 34
- Panning a PTZ Camera 35
- Figure 27: PTZ Camera at 40° 36
- Figure 28: Speed Settings 36
- Figure 29: Zoom Area 38
- Figure 30: Focus Area 38
- Figure 31: Iris Area 38
- Zooming the Camera 39
- Focusing the Camera 41
- Symbol Description 42
- GoTo preset location 42
- Define preset 42
- Delete preset 42
- Figure 38: Pattern Area 43
- Table 11: Pattern Symbols 43
- Audio/Video Configuration 44
- 4. Select Save 48
- Figure 44: OSD Parameters 49
- Table 5 – UTC Time Zones 53
- Figure 54: MJPEG Settings 61
- Figure 56: QuickTime Window 63
- Figure 57: Insert URL 63
- Figure 59: No Active Streams 64
- Figure 65: Video Settings 67
- Figure 67: Audio Settings 71
- 3. Select Save 72
- Managing System Settings 73
- Figure 72: Serial Port Modes 75
- Network Settings 78
- Changing the IP Address 81
- Figure 78: System Reset 82
- Changing the User Password 84
- Setting up the Clock 85
- Configuring the SNMP Settings 87
- Configuring Operation Mode 89
- Updating the Firmware 90
- System Administration 91
- Resetting the User Password 92
- 2. Select Save 93
- Reset to Factory Defaults 94
- Change Web Interface Language 97
- Configuring Local Storage 99
- Media Files 100
- SD Maintenance 101
- Decoding Video 102
- Video Type 103
- TECH SUPPORT: 1.888.678.9427 104
- Figure 98: MPEG-2 CODEC 105
- Figure 99: MPEG-4 CODEC 106
- Figure 100: H.264 CODEC 107
- Figure 101: MJPEG CODEC 108
- Figure 103: Audio Settings 110
- Display Configuration 111
- 7. Select OK 114
- Figure 113: URL Input Dialog 116
- RTSP URI Format 117
- General Video Parameters 118
- MJPEG Parameter 118
- MPEG-2 Parameters 118
- MPEG-4 Parameters 119
- H.264 Parameters 119
- General Audio Parameters 120
- PCMA and PCMU Parameters 120
- Multicast Parameters 120
- ComNet Customer Service 122
- Contact Information 122
© 2020, manymanuals.com. All rights reserved. | 0.512 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals