Comnet CNVETX1 Datasheet Page 14
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INS_CNVETX1_REV– 06/10/13 PAGE 14
INSTALLATION AND OPERATION MANUAL CNVETX1
TECH SUPPORT: 1.888.678.9427
Rear Panel
Figure 4: CNVETX1 Chassis Rear Panel
12-pin I/O Terminal Connector: The CNVETX1 unit provides one relay contact comprised of the
Common Contact, the Normally Closed Contact, and the Normally Open Contact. The current
through the contacts should not exceed 1 Amp @ 30 VDC load. The CNVETX1 also provides two
TTL alarm inputs. The alarm inputs are designed as a digital logic input (-0.3V to 0.6V logic 0, 1.2V
to 5V logic 1), and are pulled up by default. One RS232 port and one RS422/485 port are also
provided.
Pin-out information for the 12-pin terminal block is provided below:
Table 3: Terminal Block Connector Pinout
Pin Description Pin Description
1 GND 7 RS232 TX
2 RS422/485 TX
+
8 TTL 1
3 RS422/485 TX – 9 TTL 0
4 RS422/485 RX – 10 Relay COM
5 RS422/485 RX
+
11 Relay NC
6 RS232 RX 12 Relay NO
USB Port: The CNVETX1 provides one USB 2.0 port (port has no function and is reserved
for future use).
Ethernet port: The CNVETX1 connects to the network using a standard Ethernet cable on the
back panel.
DC Power Input: Connection to the external 12V DC power supply on the back panel.
Power over Etherne t (PoE): The CNVETX1 supports a PoE operation mode. When connected to a
PoE switch, the voltage is provided from the RJ45 connector, and the 12V DC
power input is not used.
DC Power Output: Connection to an external camera (5W Max.) on the back panel.
Solid-State Relay Outputs: Connection to 2 Solid-State relays on the back panel.
- VIDEO ENCODER/DECODER UNIT 1
- About This Guide 2
- About ComNet 3
- Contents 4
- Contents, continued 5
- Overview 6
- Abbreviations List 7
- Introduction 9
- Software Features 10
- Hardware Overview 12
- Label Description 13
- ANALYTICS Analytics Engine On 13
- PWR Power (DSP Running) 13
- Connecting the Cables 15
- Getting Started 18
- Figure 8: General Sub Menus 19
- Figure 9: The About Page 20
- Resets user password 22
- Changing system password 22
- Returns to factory defaults 22
- Changing Web Language 22
- Figure 10: Enter Password 24
- Monitoring Live Video 25
- Alarms and Contact Closures 26
- Closures 27
- 3. Select Set Relay 27
- Figure 14: PTZ Commands Page 28
- Figure 17: Connection Type 30
- Figure 20: Select Bit Count 31
- Figure 21: Select Stop Bits 32
- Figure 22: Select Parity 32
- Figure 23: PTZ Commands 33
- Table 7: PTZ Movement Control 34
- Panning a PTZ Camera 35
- Figure 27: PTZ Camera at 40° 36
- Figure 28: Speed Settings 36
- Figure 29: Zoom Area 38
- Figure 30: Focus Area 38
- Figure 31: Iris Area 38
- Zooming the Camera 39
- Focusing the Camera 41
- Symbol Description 42
- GoTo preset location 42
- Define preset 42
- Delete preset 42
- Figure 38: Pattern Area 43
- Table 11: Pattern Symbols 43
- Audio/Video Configuration 44
- 4. Select Save 48
- Figure 44: OSD Parameters 49
- Table 5 – UTC Time Zones 53
- Figure 54: MJPEG Settings 61
- Figure 56: QuickTime Window 63
- Figure 57: Insert URL 63
- Figure 59: No Active Streams 64
- Figure 65: Video Settings 67
- Figure 67: Audio Settings 71
- 3. Select Save 72
- Managing System Settings 73
- Figure 72: Serial Port Modes 75
- Network Settings 78
- Changing the IP Address 81
- Figure 78: System Reset 82
- Changing the User Password 84
- Setting up the Clock 85
- Configuring the SNMP Settings 87
- Configuring Operation Mode 89
- Updating the Firmware 90
- System Administration 91
- Resetting the User Password 92
- 2. Select Save 93
- Reset to Factory Defaults 94
- Change Web Interface Language 97
- Configuring Local Storage 99
- Media Files 100
- SD Maintenance 101
- Decoding Video 102
- Video Type 103
- TECH SUPPORT: 1.888.678.9427 104
- Figure 98: MPEG-2 CODEC 105
- Figure 99: MPEG-4 CODEC 106
- Figure 100: H.264 CODEC 107
- Figure 101: MJPEG CODEC 108
- Figure 103: Audio Settings 110
- Display Configuration 111
- 7. Select OK 114
- Figure 113: URL Input Dialog 116
- RTSP URI Format 117
- General Video Parameters 118
- MJPEG Parameter 118
- MPEG-2 Parameters 118
- MPEG-4 Parameters 119
- H.264 Parameters 119
- General Audio Parameters 120
- PCMA and PCMU Parameters 120
- Multicast Parameters 120
- ComNet Customer Service 122
- Contact Information 122
© 2020, manymanuals.com. All rights reserved. | 8.453 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals